Manual wheelchair debugging method

Simple structure of wheelchair (non-electric wheelchair)

Wheelchair installation and commissioning (non-electric wheelchair):

1.  Pedal adjustment

Three-step adjustable foot pedal adjustment: Use a 5mm hexagon wrench in the on-board tool bag to loosen the pedal screws. According to the occupant's height and leg length, adjust the pedal height to a suitable position, and then lock it with a hexagonal wrench.

Oblique wedge-locked foot pedal adjustment: Use an open-end wrench to loosen the oblique wedge nut, adjust it to an appropriate position, and lock it.

Hoop type foot pedal adjustment: Use an open-handed hand to loosen the hoop nut, adjust it to an appropriate position and lock it.

Note: Adjustable foot pedal should be adjusted to a height of more than 50mm from the ground.

2.Moving leg parts installation and removal

Installation: ① align the gusset plate hole with the spring pin on the wheelchair, hang the movable leg, and then rotate in the direction of the arrow. When you hear a "click", the installation is completed.

② install the leg strap.

Removal: ① remove the leg strap. ② open the gusset plate, rotate it outwards and take it out upward. Note: after the movable leg is installed, it must be confirmed whether it is fixed to avoid accidents.

3.Height adjustment of lifting leg

Raise: hold the movable bracket and lift it up to a proper height

Lower: hold the handle with the right hand, press in the direction of the arrow, and press the movable leg with the left hand to the appropriate height.

4. Operation method of movable handrail

Reversible handrail: press and hold the handrail buckle to separate the buckle from the frame, and then turn it back.

Removable handrail: press and hold the spring pin at the front of the handrail tube with one hand to separate the spring pin from the frame pipe fitting, hold the back of the handrail tube with the other hand and take it out upward. If there is a locking mechanism, first open the locking mechanism, then hold the handrail and take it out upward.

5. Adjustable handrail height adjustment

When the wrench is pulled on one hand and the handrail is lifted on the other hand to a suitable height, release the wrench and lock the spring pin with a click.

6. Installation of pedestal pan

After the wheelchair is deployed. Take out the pedestal pan, hold the pedestal pan with both hands (the opening is forward), clamp the plastic clip on one side of the pedestal tube, press it down into the other side, and confirm that all the plastic clips have been clamped into the pedestal tube before use.

Warning: please make sure that all four fasteners are stuck in the seat tube to avoid accidents.

7. Seat core and bedpan

Core pulling out: grasp the front end of the core and pull it out.

Insert the seat core: grasp the front end of the seat core and insert it inwards. Take out the bedpan: grasp the handle at the front of the bedpan and pull out the bedpan in the direction of the arrow.

Place the bedpan: grasp the front handle of the bedpan, insert the bedpan into the slide under the cushion from the back, and confirm the fixation.

8. Installation of headrest

Installation: hold the headrest with both hands, and insert the pipe fitting hole at the back in the direction of the arrow in the figure.

Put up: hold the headrest with both hands and pull it up and out.

9. Anti roll wheel detachable adjustment

Press down button of spring pin and pull out anti roll.

10. Back angle adjustment

 Half lying type: ① pull down the left and right armrest knobs with both hands at the same time, and use the gravity behind the body to reach the required position.

② keep the sitting position, release the handle knob, and the locating pin can be popped into the locating hole.

Fully lying type: hold the handlebar with both hands, hold the handlebar slowly: down, when reaching the required position, release the handlebar. For safety, please check the lifting mechanism regularly. (please check whether the wheelchair is equipped with anti roll tube before use).

Note: please do not extend your finger into the connection between the upper end of the handle and the pipe fitting during the half lying adjustment, which is dangerous.

Warning: do not adjust the back leaning angle at the place with slope, which may cause rollover hazard.

Warning: please don't lean on your back when you are fully lying down to avoid accidents.